Products

ATV Harness Description

This harness is used with the JD 2630 display and GPS receiver to perform field mapping for soil sampling, etc. The harness includes:

  • 12V plug for power; maintains constant power to the display and StarFire® Receiver. (A separate toggle switch de-activates the Display, when leaving ATV for a short time allowing the display memory to remain active.)
  • JD 2630 Display connector
  • GPS StarFire® Receiver connector
  • CAN Bus Terminator
  • Toggle switch for standby mode

More information

If this is to be used with a vehicle (i.e. Pickup truck, etc.) as opposed to an ATV, a six (6) foot extension harness is available to extend the GPS receiver to the roof. See Extension

WireManagers offers three (3) sets of video harnesses that take advantage of the three (3) video inputs on the JD 2630 display. The harness extends from the JD 2630 display to the outside rear of the cab. It is intended for use with cabs that are not pre-wired with the video inputs, or, where the cab harness does not have ALL three (3) video inputs pre-wired. The harnesses include:

  • JD 2630 video input connector
  • Auxiliary power connector that connects to the 12v power strip to provide power to the cameras
  • video adapter for each of the most popular video cameras (CabCam, VisionWorks, VOYAGER and AGCAM)

https://wiremanagers.com/index.php/product/wm-120-3/

WM120-3 VIDEO Camera Cab Harness  for three (3) CabCam or VisionWorks cameras.

More information

WM124-3 VIDEO Camera Cab Harness  for three (3) VOYAGER cameras.

More information

WM128-3 VIDEO Camera Cab Harness  for three (3) AGCAM cameras.

More information

WireManagers offers Video Camera Adapters for use with video connectors located outside of JD Cabs. The available adapters are as follows:

  • WM 120-990 4 Series Sprayer -Video Adapter- two (2) CabCam or VisionWorks cameras
  • WM 128-990 4 Series Sprayer -Video Adapter, two (2) AgCam cameras
  • WM 128-834 JD Tractor Hitch Video Camera Adapter, one (1) AgCam Camera
  • WM 120-834 JD Tractor Hitch Video Camera Adapter, one (1) CabCam Camera
  • WM 120-2 VIDEO ADAPTER – Voyager display to CabCam/VisionWorks camera

 

WM 120-990 4 Series Sprayer -Video Adapter- two (2) CabCam or VisionWorks cameras

More information

 

WM 128-990 4 Series Sprayer -Video Adapter, two (2) AgCam cameras

More information

 

WM 128-834 JD Tractor Hitch Video Camera Adapter, one (1) AgCam Camera

More information

 

WM 120-834 JD Tractor Hitch Video Camera Adapter, one (1) CabCam Camera

More information

 

WM 120-2 VIDEO ADAPTER – Voyager display to CabCam/VisionWorks camera

 

More information

The following harness extensions allow the JD 2630 display to be re-positioned.

WM 81213-2 Cab Display re-positioning Extension, two (2) Ft. (0.6m)

WM 81213-4 Cab Display re-positioning Extension, four (4) Ft. (1.2m)

WireManagers offers extension harnesses to allow the display and/or video cameras to be located on the ground for demonstration and training purposes.

This set of harnesses extends the circular connector on the B-post to the ground. The display adapter remains with the display and attaches to the extension harness. There are two lengths:

  • WM 81213-25 Display Extension for Training,12 circuits, Male/Female 25 Ft. (7.6m)
  • WM 81213-30 Display Extension for Training, 12 Circuits, Male/Female 30 Ft. (8.5m)

These two harnesses extend the circular connector on the B-post to the ground and attaches directly to connector V1 on the 2630 display.

  • WM 80795-A25 Bulkhead (Cab Corner Post) Extension Harness -25Ft (7.6m)
  • WM 80795-A35 Cab Corner Post to Display Ext. Harness – 35Ft (10.7m)

 

These two harness sets consist of the same B-post to V1 display connection as above and also has a shorter video harness that connects to the V2 connector on the display and has a 10 foot power connection to the power strip as well as an adapter to connect to video cameras.

  • WM 80795-AV25 Extension Harness Bundle( GS3-2630 and Video Camera Harnesses) 25 Feet (7.6m)
  • WM 80795-AV35 -Extension Harness Bundle (GS3-2630 and Video Camera Harness) 35 Feet (10.7m)

WM 45 TERMINATOR for Deere® wire harnesses. Fits the 6-way CAN connector.

 

Services

Prototype Harness Mfg

Production Harness Process

WM has extensive experience producing prototype harness for a major Agricultural OEM. The harnesses have ranged from small six (6) inch adapters up to large 50 foot harnesses with 70+ connectors.

We have traditionally been able to ship prototype harnesses within ten (10) working days (M-F) after receipt of PO. This is policy is dependent upon the availability of the connectors, terminals, wire seals and any other harness components.

Problems in the past that have caused potential shipping delays:

          Design changes

          Print mistakes (i.e. connector/terminal inconsistencies)

          Unique or hard to get parts

          Quantity and/or complexity of harness

          Identifying component mfr’s part numbers from customers’ part number

          Calculating wire lengths for large harnesses

 Process:

A)      Initial Process

          Send hard copy or pdf of prints. (other formats may be a problem)

          We review all prints for inconsistencies. (Note: we will need the e-mail address of ONE person to contact to answer any and all questions we may have.)

          If an Excel file of the wire table is available, that speed up the quoting process

          A quote is usually available within 48 hours

B)      Mfg Process

          When the quote is accepted, and PO received, we then begin ordering material and begin the production process. (Terms are NCNR, Net/10)

          As the process continues, we will keep you updated as needed

          Upon completion, ALL harnesses are 100% circuit checked

C)      Shipping

          When parts are shipped, an e-mail will be sent giving you the shippers tracking number (NOTE: UPS has a large depot nearby and is our preferred shipper. Please provide us with you preferred shipper and shipping account number.)

          The invoice will be sent via e-mail

 

NOTE:Should there be a need for any rework or repair, we need to mutually agree upon the process and conditions .

WM is willing to provide contract mfg services to meet your partial or complete assembly needs. Please contact us to discuss.

Error: Contact form not found.

WM has experience building custom harness for older cars. the process involves either

  • obtaining a drawing of the harness, or
  • obtaining the actual harness and backward engineering it.

In one instance WM was sent the harness from a 1939 Chevy Coupe and we were able to successfully find al of he parts and assemble a new harness.